Vent-Sure Downdraft Kiln Vent System for L&L kilns part# M-V-VENT/00
Vent-Sure for 120 Volts with 8 foot flex duct
A Critical component in the longevity of your kiln!The Vent-Sure automatic kiln vent helps prevent corrosion on the inside and outside of your kiln
Removes Fumes
The vent blower motor is normally mounted with the 12" outlet protruding through a wall.
This keeps the heat of the kiln away from the motor (for long motor life) and keeps the motor vibration away from the kiln.
The vent tubing is kept under vacuum instead of pressure.
This ensures that any leak in the tubing does not blow noxious fumes into your room.
Large Capacity
The blower vents up to 130 CFM (cubic feet per minute).
This will handle up to a 20 cubic foot kiln (and usually larger). More than one vent can be attached to a kiln.
Minimal Electrical Power
The motor only pulls 1.37 amps on 120 volts.
The blower motor features a 6-foot long 120-volt 15-amp power cord. An On/Off switch is located on the cord.
240-volt models are available.
Adjustable Vent Control
An adjustable slide on the bypass/collection box adjusts the amount of venting from the system.
Adjust the vent to your kiln size so no heat is wasted.
8 feet of flexible aluminum duct
8 feet of flexible and expandable aluminum 3" diameter duct is included along with necessary hose clamps.
Longer lengths or lengths of 3" stove pipe can also be used
Length can be as great as 60 feet horizontal or vertical with up to four 90-degree bends.
A separate 15-foot flexible duct is available for longer runs.
Three-Year Limited Warranty
Because of our unique wall-mount fan, we rarely replace fan motors.
MET Listed to UL499 Standards
The VENT-SURE Model VS-1 is c-MET-us listed for use with all c-MET-us listed L&L kilns.
It is MET-us listed for all MET-us listed L&L kilns.
Note that using a non-L&L vent (even if listed to UL499) on an L&L kiln (or an L&L vent on a non-L&L kiln) would not be listed to UL499.
Included Multi-Mounting Bracket
A special Multi-mounting bracket (M-V-MULT/00) is included with all vents to mount the vent motor elevated off the floor (increasing motor life) or point the outlet vertically for ceiling installations.
Vent-Sure for 120 Volts with 8 foot flex duct
A Critical component in the longevity of your kiln!The Vent-Sure automatic kiln vent helps prevent corrosion on the inside and outside of your kiln
Removes Fumes
The vent blower motor is normally mounted with the 12" outlet protruding through a wall.
This keeps the heat of the kiln away from the motor (for long motor life) and keeps the motor vibration away from the kiln.
The vent tubing is kept under vacuum instead of pressure.
This ensures that any leak in the tubing does not blow noxious fumes into your room.
Large Capacity
The blower vents up to 130 CFM (cubic feet per minute).
This will handle up to a 20 cubic foot kiln (and usually larger). More than one vent can be attached to a kiln.
Minimal Electrical Power
The motor only pulls 1.37 amps on 120 volts.
The blower motor features a 6-foot long 120-volt 15-amp power cord. An On/Off switch is located on the cord.
240-volt models are available.
Adjustable Vent Control
An adjustable slide on the bypass/collection box adjusts the amount of venting from the system.
Adjust the vent to your kiln size so no heat is wasted.
8 feet of flexible aluminum duct
8 feet of flexible and expandable aluminum 3" diameter duct is included along with necessary hose clamps.
Longer lengths or lengths of 3" stove pipe can also be used
Length can be as great as 60 feet horizontal or vertical with up to four 90-degree bends.
A separate 15-foot flexible duct is available for longer runs.
Three-Year Limited Warranty
Because of our unique wall-mount fan, we rarely replace fan motors.
MET Listed to UL499 Standards
The VENT-SURE Model VS-1 is c-MET-us listed for use with all c-MET-us listed L&L kilns.
It is MET-us listed for all MET-us listed L&L kilns.
Note that using a non-L&L vent (even if listed to UL499) on an L&L kiln (or an L&L vent on a non-L&L kiln) would not be listed to UL499.
Included Multi-Mounting Bracket
A special Multi-mounting bracket (M-V-MULT/00) is included with all vents to mount the vent motor elevated off the floor (increasing motor life) or point the outlet vertically for ceiling installations.
Vent-Sure for 120 Volts with 8 foot flex duct
A Critical component in the longevity of your kiln!The Vent-Sure automatic kiln vent helps prevent corrosion on the inside and outside of your kiln
Removes Fumes
The vent blower motor is normally mounted with the 12" outlet protruding through a wall.
This keeps the heat of the kiln away from the motor (for long motor life) and keeps the motor vibration away from the kiln.
The vent tubing is kept under vacuum instead of pressure.
This ensures that any leak in the tubing does not blow noxious fumes into your room.
Large Capacity
The blower vents up to 130 CFM (cubic feet per minute).
This will handle up to a 20 cubic foot kiln (and usually larger). More than one vent can be attached to a kiln.
Minimal Electrical Power
The motor only pulls 1.37 amps on 120 volts.
The blower motor features a 6-foot long 120-volt 15-amp power cord. An On/Off switch is located on the cord.
240-volt models are available.
Adjustable Vent Control
An adjustable slide on the bypass/collection box adjusts the amount of venting from the system.
Adjust the vent to your kiln size so no heat is wasted.
8 feet of flexible aluminum duct
8 feet of flexible and expandable aluminum 3" diameter duct is included along with necessary hose clamps.
Longer lengths or lengths of 3" stove pipe can also be used
Length can be as great as 60 feet horizontal or vertical with up to four 90-degree bends.
A separate 15-foot flexible duct is available for longer runs.
Three-Year Limited Warranty
Because of our unique wall-mount fan, we rarely replace fan motors.
MET Listed to UL499 Standards
The VENT-SURE Model VS-1 is c-MET-us listed for use with all c-MET-us listed L&L kilns.
It is MET-us listed for all MET-us listed L&L kilns.
Note that using a non-L&L vent (even if listed to UL499) on an L&L kiln (or an L&L vent on a non-L&L kiln) would not be listed to UL499.
Included Multi-Mounting Bracket
A special Multi-mounting bracket (M-V-MULT/00) is included with all vents to mount the vent motor elevated off the floor (increasing motor life) or point the outlet vertically for ceiling installations.